3-axle low-loader trailer with wheel recesses for transporting construction machinery
Product benefits and optional extras
- Wheel recesses integrated in external frame, coordinated with floor construction incl. drive-on aluminium cover
- Wheel recesses with drive-on aluminium cover
- Wheel recesses in different designs for transporting special construction vehicles
- High point loading due to narrow cross member spacing
- Pull-out extensions, incl. extension planks for transporting wide loads
- Excavator shovel recess between cross members at rear
- Central storage compartment with lockable lid on raised platform
- Installation of axles from well-known manufacturers such as SAF or BPW
- OPTIONAL: Offset drawbar with pivoting eye 40 + 50 mm
- OPTIONAL: 2-part loading ramps with motor-hydraulic ramp actuators
- OPTIONAL: Ramps with hydraulic lateral movement, operated on semitrailer
- OPTIONAL: Plug-in retaining rails
Vehicle details
TYPE DESIGNATION
- 3-AXLE LOW LOADER TRAILER WITH WHEEL RECESSES FOR TRANSPORTING CONSTRUCTION MACHINERY
FRAME
- Welded steel construction with flat front frame offset or body offset and drive-on taper at rear with externally welded square ribs
- 4 pairs of mounting pockets for 80 x 40 mm tubular posts in external frame
- Recess in access slope for excavator shovel linkage
- 3 pairs of lashing points in external frame
- 5 pairs of recessed 5 t lashing rings in floor
- 2 pairs of wheel recesses behind front offset with aluminium covers,
- approx. 1,150 mm long at bottom and approx. 535 mm long at rear between 2nd and 3rd axles, front wheel recess approx. 270 mm deep and rear recess approx. 220 mm deep.
CHASSIS
- Reinforced, maintenance-free parabolic springs
- Low-loader axles, each with 11 t axle load
- S-cam brake 300/200 mm, autom. brake linkage adjuster
- Dual-axle compensation
- Tyres :
- 12 x 245/70 R 17.5 143J, manufacturer as per factory specifications
- 12 steel wheel rims 6.75 x 17.5, 10-hole, with rim offset, silver ex-works
BRAKE SYSTEM
- Brake system according to EC Directive 71/320 or ECE R13
- Two-line brake
- EBS - electronic brake system
- Wabco 4S3M = 1st and 2nd axles sensed
- Spring-loaded parking brake on 2nd and 3rd axles
- Steel air tank
FLOOR
- Softwood floor 50 mm, waterproofed, protruding approx. 5 - 10 mm beyond frame profiles or beyond steel stud plate cover over rear wheels
EXTENSION
- Foldable = pivoting extensions, on both sides of drop deck and rear
- taper incl. continuous wooden boarding = also floor boards
- between side members when used without extensions (however, track width of construction machines/vehicles to be transported must not exceed the external frame width of 2,550 mm)
- 2 removable warning signs at both front and rear
RAMPS
- 2 foldable, 1-part loading ramps, approx. 2,700/700 mm, with hardwood flooring and with externally welded square ribs
- Ramp width manually adjustable by approx. 550 mm, with rod,
- (min. spacing approx. 295 mm up to max. total width of 2,815 mm)
- lockable in driving position using chains with turnbuckle
- 2 autom. folding supports at rear
ELECTRICAL EQUIPMENT
- 24 V lighting system according to EC Directive 76/756/EWG
- 2 five-chamber LED tail lights on ramps
- LED side marker lights
- 2 position or contour lights in each case, extendible to 3,000 mm
- Fixed cable(s) with 2 x 7-pin or 1 x 15-pin connector
- Bracket incl. revolving beacon on left ramp, with connecting cable and
PAINTWORK
- Blasted with steel granulate, treated with zinc dust primer and spray painted 2-component acrylic paints for commercial vehicles
- Plastic and hot-dip galvanised parts (extensions etc.) unpainted,
- powder-coated attachments/installation parts and drawbar black
ACCESSORIES
- Rear markings as per ECE standards
ATTACHMENTS
- Wheel chock(s) as per regulations
- Plastic mudguards or splashguards with spray protection as per regulations
- Side impact protection
- Spare wheel well for 1 spare wheel
- 1 accessory compartment at front centre of raised platform, with folding lid
- Externally welded square ribs on ramps and rear access slope
- Centre of gravity marking
- Brackets for extension planks on frame
BRIDGE PLATFORM
- Approx. 2,100/2,550 mm = raised platform at front incl. frame offset, tapered corners
CONTOUR MARKINGS
- Reflective contour marking strips across entire length of sides and on the rear (white on sides and red at rear by default), according to ECE 48
Impressions
2 folding single-part loading ramps with hardwood flooring
Wheel recesses with drive-on aluminium cover
Excavator shovel recess between side members at rear
Pull-out extensions incl. extension planks for transporting wide loads
OPTIONAL: Offset drawbar with pivoting eye, 40 + 50 mm
Wheel recesses in different designs for transporting special construction vehicles
Wheel recesses integrated in external frame, coordinated with floor construction incl. drive-on aluminium cover
Wheel recesses in different designs for transporting special construction vehicles
Your Schwarzmüller contacts
Always close to you. We are here for you.
Premium customer service, too
From maintenance to rental vehicles
Schwarzmüller Service App
Rely on our top services – also mobile. The app serves as a helper in an emergency in the event of a breakdown and is even available offline.
