4-axle low-loader semitrailer with offset platform

  • High point loading due to narrow cross member spacing
  • Offset platform raised at the front incl. plug-in side walls
  • Drop-deck loading platform with softwood floor and tubular posts in external frame
  • Pull-out extensions, incl. extension planks for transporting wide loads
  • Loading ramps with hardwood flooring and welded square ribs
  • Recessed foldable lashing rings on drop deck, and lashing points on external frame
  • Third and fourth axles are steered trailing axles for improved cornering and lower tyre wear
  • Pull-out/removable warning signs front and rear, incl. position and marker lights for wide loads
  • Installation of axles from well-known manufacturers such as SAF or BPW
  • OPTIONAL: 2-part loading ramps with motor-hydraulic ramp actuators
  • OPTIONAL: Ramps with hydraulic lateral movement, operated on semitrailer
  • OPTIONAL: Wheel recesses for transporting special vehicles

TYPE DESIGNATION

  • 4-AXLE LOW LOADER SEMITRAILER

DIMENSIONS

  • approx. 3,500/2,550 mm or approx. 2,480 mm between side walls = front offset platform
  • Approx. 8,300/2,550 mm = drop-deck platform - flat load surface
  • Approx. 1,000/2,550 mm = rear access slope
  • Total width: approx. 2,550 mm or approx. 3,000 mm with extension
  • Loading height, laden: approx. 900 mm
  • Horizontal position of semitrailer at fifth-wheel height: laden approx. 1,220 mm

FRAME

  • Welded steel construction with tapered frame offset at front
  • and drive-on taper at rear
  • Replaceable 3.5" kingpin (slew radius on truck at rear max: 2,100 mm)
  • 5 pairs of mounting pockets on drop deck incl. tubular posts 100 x 50 x 5 mm, useful height approx. 1,000 mm, hot-dip galvanised
  • 5 pairs of lashing points on external frame
  • 10 recessed lashing eyes in the drop-deck section
  • Storage for extension planks below loading platform when not in use

CHASSIS

  • Air suspension with lifting and lowering device, for loading and unloading
  • Automatic adjustment of driving level from 15 km/h
  • Air-sprung low-loader unit with low-maintenance axles.
  • 4 x 10 t, (technical 4 x 12 t) wheelbase 3 x 1.310 mm.
  • S-cam brake 300/200 mm, autom. brake linkage adjuster.
  • 1st and 2nd axles rigid,
  • Third and fourth axles steering knuckle = friction-steered trailing
  • (20° steering angle) incl. electropneum. reverse gear interlock with switch operation
  • in cab and additional operation on semitrailer.
  • Lifting first axle = raised or lowered automatically according to weight (with the lifting axle raised, the loading or total height increases by approx. 50 mm) as well as forced lowering autom. lifting axle, incl. integrated speed-restricted moving-off, with button operation in cab (no button on our part)
  • Tyres :
  • 16 x 245/70 R 17,5, 146/146F, manufacturer as per factory specifications
  • 16 steel wheel rim, 10-hole, with rim offset, silver ex-works

SUPPORT FIXTURES

  • Mechan. 2 x 12 t support jacks, single-sided operation and thrust compensation

BRAKE SYSTEM

  • Brake system according to EC Directive 71/320 or E CE R13
  • Two-line brake
  • EBS - electronic brake system
  • Wabco 2S2M = one axle sensed
  • RSS - stability program
  • Spring-loaded parking brake
  • Steel air tank

FLOOR

  • Softwood floor 50 mm, waterproofed, protruding beyond frame profiles by approx. 5 mm at offset platform and 15 mm on drop deck, or beyond steel stud plate cover over rear wheels

EXTENSION

  • Pull-out extensions, on both sides of drop deck and rear taper, incl.
  • continuous wooden boarding, extending parts hot-dip galvanised
  • 2 pull-out/removable warning signs each at front and rear

RAMPS

  • 2 foldable, 1-part loading ramps, approx. 2,700/700 mm, with hardwood flooring
  • Ramp width manually adjustable by approx. 580 mm, with rod,
  • (min. spacing approx. 265 mm up to max. total width of 2,850 mm)
  • lockable in driving position using chains with turnbuckle
  • 2 autom. folding supports at rear
  • Lifting aid with coil spring

ELECTRICAL EQUIPMENT

  • 24 V lighting system according to EC Directive 76/756/E WG
  • 2 five-chamber tail lights on ramps
  • LED side marker lights
  • 2 clearance lamps
  • 2 contour lights
  • 2 x 7-pin sockets at front

PAINTWORK

  • Blasted with steel granulate, treated with zinc dust primer and spray painted 2-component acrylic paints for commercial vehicles
  • Side and rear walls anodised
  • Plastic and hot-dip galvanised parts unpainted,
  • powder-coated attachments/installation parts black

ACCESSORIES

  • Rear markings as per ECE standards

ATTACHMENTS

  • Wheel chock(s) as per regulations
  • Plastic mudguards or splashguards with spray protection as per regulations
  • Spare wheel well for 1 spare wheel
  • Side impact protection
  • Pull-out/removable warning signs front and rear, incl. position and
  • marker lights for wide loads up to 3,000 mm
  • Externally welded square ribs on ramps and rear access slope

WALLS/POSTS

  • Plug-in side walls on offset platform, 400 mm high
  • Steel front wall,, 25 mm aluminium hollow profile walls at sides and rear, with latch-type tension locks, plug-in rear corner posts in side wall height

CONTOUR MARKING

  • Reflective contour marking strips across entire length of sides and on the rear (white on sides and red at rear by default), according to ECE 48
back to the overview Export page as PDF

Do you have any questions?

Write to us

Your Schwarzmüller contacts

Always close to you. We are here for you.

Search for a contact person

Premium customer service, too

From maintenance to rental vehicles

Read more

3-axle low-loader trailer with wheel recesses for transporting construction...3-axle low-loader trailer with wheel recesses for transporting construction machinery3-axle low-loader semitrailer with offset platform3-axle low-loader semitrailer with offset platform