3-axle low loader trailer with wheel recesses for transporting construction machinery

Product benefits

  • Wheel recesses integrated in external frame, coordinated with floor construction incl. drive-on aluminium cover
  • Wheel recesses with drive-on aluminium cover
  • Wheel recesses in different designs for transporting special construction vehicles
  • High point loading due to narrow cross member spacing
  • Pull-out extensions, incl. extension planks for transporting wide loads
  • Excavator shovel recess between cross members at rear
  • Central storage compartment with lockable lid on raised platform
  • Installation of axles from well-known manufacturers such as BPW, Mercedes or SAF
  • OPTIONAL: Offset drawbar with pivoting eye 40 + 50 mm
  • OPTIONAL: 2-part loading ramps with motor-hydraulic ramp actuators
  • OPTIONAL: Ramps with hydraulic lateral movement, operated on semitrailer
  • OPTIONAL: Plug-in retaining rails

Product details



3-axle low loader trailer with wheel recesses for transporting construction machinery


Bridge platform


Approx. 2,100/2,550 mm = raised platform at front incl. frame offset, tapered corners
Approx. 5,500 or 6,100/2,550 mm = drop-deck platform - flat load surface or external surfaces advanced
Approx. 1,010/2,550 mm = rear access slope
Total width: approx. 2,550 mm or approx. 3,000 mm with extension
Loading height, unladen: approx. 940 mm

Frame


Welded steel construction with flat front frame offset or body offset and drive-on taper at rear with externally welded square ribs
4 pairs of mounting pockets for 80 x 40 mm tubular posts in external frame
Recess in access slope for excavator shovel linkage
3 pairs of lashing points in external frame
5 pairs of recessed 5 t lashing rings in floor

2 pairs of wheel recesses behind front offset with aluminium covers,
approx. 1,150 mm long at bottom and approx. 535 mm long at rear between 2nd and 3rd axles, front wheel recess approx. 270 mm deep and rear recess approx. 220 mm deep.

Chassis


Reinforced, maintenance-free parabolic springs

Low-loader axles, each with 11 t axle load
S-cam brake 300/200 mm, autom. brake linkage adjuster
Dual-axle compensation

Tyres :
12 x 245/70 R 17.5 143J, manufacturer as per factory specifications
12 steel wheel rims 6.75 x 17.5, 10-hole, with rim offset, silver ex-works

Drawgear


Fixed drawbar, 1,800 mm long, 40 mm drawbar eye, 5° angle,
with silent bushing

Brake system


Brake system according to EC Directive 71/320 or ECE R13
Two-line brake
EBS - electronic brake system
Wabco 4S3M = 1st and 2nd axles sensed
Spring-loaded parking brake on 2nd and 3rd axles
Steel air tank

Floor


Softwood floor 50 mm, waterproofed, protruding approx. 5 - 10 mm beyond frame profiles or beyond steel stud plate cover over rear wheels

Extension


Foldable = pivoting extensions, on both sides of drop deck and rear
taper incl. continuous wooden boarding = also floor boards
between side members when used without extensions (however, track width of construction machines/vehicles to be transported must not exceed the external frame width of 2,550 mm)
2 removable warning signs at both front and rear
Position and marker lights extendible to 3,000 mm

Ramps


2 foldable, 1-part loading ramps, approx. 2,700/700 mm, with hardwood flooring and with externally welded square ribs
Ramp width manually adjustable by approx. 550 mm, with rod,
(min. spacing approx. 295 mm up to max. total width of 2,815 mm)
lockable in driving position using chains with turnbuckle
2 autom. folding supports at rear

Electrical equipment


24 V lighting system according to EC Directive 76/756/EWG
2 five-chamber LED tail lights on ramps
LED side marker lights
2 position or contour lights in each case, extendible to 3,000 mm
Fixed cable(s) with 2 x 7-pin or 1 x 15-pin connector
Bracket incl. revolving beacon on left ramp, with connecting cable and
socket on end plate

Paintwork


Blasted with steel granulate, treated with zinc dust primer and spray painted 2-component acrylic paints for commercial vehicles
Plastic and hot-dip galvanised parts (extensions etc.) unpainted,
powder-coated attachments/installation parts and drawbar black

Contour markings


Reflective contour marking strips across entire length of sides and on the rear (white on sides and red at rear by default), according to ECE 48

Accessories


Rear markings as per ECE standards

Attachments


Wheel chock(s) as per regulations
Plastic mudguards or splashguards with spray protection as per regulations
Side impact protection
Spare wheel well for 1 spare wheel
1 accessory compartment at front centre of raised platform, with folding lid
Externally welded square ribs on ramps and rear access slope
Centre of gravity marking
Brackets for extension planks on frame

Product impressions