3-axle low loader semitrailer with offset platform - reinforced

Product benefits

  • High point loading due to narrow cross member spacing
  • Offset platform raised at the front incl. plug-in side walls
  • Drop-deck loading platform with softwood floor and tubular posts in external frame
  • Pull-out extensions, incl. extension planks for transporting wide loads
  • Loading ramps with hardwood flooring and welded square ribs
  • 4 recessed foldable lashing rings on drop deck, and 5 pairs of lashing points on external frame
  • Pull-out/removable warning signs front and rear, incl. position and marker lights for wide loads
  • Facility for storing extension planks below loading platform when not in use
  • Installation of axles from well-known manufacturers such as BPW or SAF
  • OPTIONAL: 2-part loading ramps with motor-hydraulic ramp actuators
  • OPTIONAL: Wheel recesses for transporting special vehicles
  • OPTIONAL: Plug-in retaining rails

Product details



3-AXLE LOW LOADER SEMITRAILER - reinforced



Weights


Gross train weight (perm.): 40 t
Gross weight (techn.): 48 t
Axle assembly load (techn.): 30 t
Fifth-wheel load (techn.): 18 t - for 3-axle STT
Tare weight: approx. 9. 1 t

Dimensions


Approx. 3,500 mm = front offset platform
Approx. 7,800 mm = drop-deck platform - flat load surface
Approx. 1,000 mm = rear access slope
Total width: approx. 2,550 mm or approx. 3,000 mm with extension
Platform width: approx. 2,480 mm between side walls on offset platform

Fifth-wheel height, unladen: approx. 1,2 5 0 mm (= approx. horizontal position of semitrailer)
Loading height, laden: approx. 920 mm
Loading height, unladen: approx. 950 mm

Frame


Welded steel construction with tapered frame offset at front
and drive-on taper at rear
Replaceable 2" kingpin (EC installation dimension, width across corners: 2,040 mm)
2 folding supports at end of frame
5 pairs of mounting pockets on drop deck incl. tubular posts 100 x 50 x 5 mm,
useful height approx. 1,000 mm, hot-dip galvanised
5 pairs of lashing points on external frame
4 pairs of recessed foldable 5 t lashing rings (10 t techn. tensile strength) on drop deck =
Arrangement:
1st pair on the tapered frame offset
2nd pair after the frame offset
3rd pair approx. at the height of the 2nd axle in the drop-deck section
4th pair in front of the rear access slope

Storage for extension planks below loading platform when not in use.

Chassis


Air suspension with lifting and lowering device, for loading and unloading
Automatic adjustment of driving level from 15 km/h

Air-sprung low-loader unit with low-maintenance axles
3 x 10 t, wheelbase 2 x 1,310 mm
S-cam brake 300/200 mm, autom. brake linkage adjuster
1st and 2nd axles rigid,
steering knuckle 3rd axle = friction-steered trailing axle (20° steering angle) incl. electropneum. reverse gear interlock with switch operation in cab and additional operation on semitrailer

Tyres :
12 x 2 4 5/7 0 R 17.5 14 3 J, manufacturer as per factory specifications
12 steel wheel rims 6.75 x 17.5, 10-hole, with rim offset, silver

Support fixtures


Mechan. 2 x 12 t support jacks, single-sided operation and thrust compensation, manufacturer as per factory specifications

Brake system


Brake system according to EC Directive 71/320 or E CE R13
Two-line brake, configured for 30 t axle load
EBS - electronic brake system
Wabco 2S2M = one axle sensed
RSS - stability program
Spring-loaded parking brake
Steel air tank

Floor


Softwood floor 50 mm, waterproofed, protruding beyond frame profiles by approx. 5 mm at offset platform and 15 mm on drop deck, or beyond steel stud plate cover over rear wheels

Walls/posts


Plug-in side walls on offset platform, 400 mm high, steel front wall,
25 mm aluminium hollow profile walls at sides and rear, with latch-type tension locks, plug-in rear corner posts in side wall height

Extension


Pull-out extensions, on both sides of drop deck and rear
taper incl. continuous wooden boarding, extending parts hot-dip galvanised

Ramps


2 foldable, 1-part loading ramps, approx. 2,700/700 mm, with hardwood flooring
Ramp width manually adjustable by approx. 580 mm, with rod,
(min. spacing approx. 265 mm up to max. total width of 2,850 mm)
lockable in driving position using chains with turnbuckle
Lifting aid with coil spring

Electrical equipment


24 V lighting system according to EC Directive 76/756/E WG
2 five-chamber tail lights on ramps
LED side marker lights
1 extendible clearance lamp/marker light on each warning sign for transport of wide loads up to 3 m
2 x 7-pin sockets at front
2-pin socket at rear for revolving beacon.

Paintwork


Blasted with steel granulate, treated with zinc dust primer and spray painted 2-component acrylic paints for commercial vehicles (standard RAL or truck colour)

Side and rear walls anodised (natural aluminium)
(for manufacturing reasons, colour deviations are possible in the case of anodised components)
Plastic and hot-dip galvanised parts unpainted,
powder-coated attachments/installation parts black

Reflective contour marking strips across entire length of sides and on the rear (white on sides and red at rear by default), according to ECE 48

Accessories


Rear markings as per ECE standards

Attachments


Wheel chock(s) as per regulations
Plastic mudguards or splashguards with spray protection as per regulations
Spare wheel well for 1 spare wheel
Side impact protection
Pull-out/removable warning signs front and rear, incl. position and
marker lights for wide loads up to 3,000 mm
Externally welded square ribs on ramps and rear access slope
Centre of gravity marking

Product impressions