2-axle low loader trailer with straight platform

Product benefits

  • High point loading due to narrow cross member spacing
  • Waterproofed softwood floor, protruding beyond frame profiles
  • 2 pairs of recessed foldable lashing rings
  • 4 pairs of lashing points on external frame
  • Installation of axles from well-known manufacturers such as BPW or SAF
  • OPTIONAL: Foldable, pivoting extensions, incl. extension planks for transporting wide loads
  • OPTIONAL: Offset drawbar with pivoting eye 40 + 50 mm
  • OPTIONAL: Version with side walls
  • OPTIONAL: 2-part loading ramps with motor-hydraulic ramp actuators
  • OPTIONAL: Ramps with hydraulic lateral movement, operated on semitrailer
  • OPTIONAL: Plug-in retaining rails

Product details



2-AXLE LOW LOADER TRAILER - TYPE TÜP



Weights


Gross weight (techn.): 20 t
Payload: approx. 15.6 t
Gross weight (perm.): 18 t
Tare weight: approx. 4. 3 t

Dimensions


Approx. 5,000 mm = drop-deck platform - flat load surface
Approx. 1,000 mm = rear access slope
Total width: 2,550 mm
Loading height, laden: approx. 950 mm

Frame


Welded steel construction without front frame offset or body offset
and drive-on taper at rear
4 pairs of lashing points under external frame
2 pairs of recessed foldable 5 t lashing rings in floor (10 t techn. tensile strength)

Chassis


Reinforced, maintenance-free parabolic springs

Low-loader axles, each with 11 t axle load
S-cam brake 300/200 mm, autom. brake linkage adjuster

Tyres :
8 x 2 4 5/7 0 R 17.5 14 3 J, manufacturer as per factory specifications
8 steel wheel rims 6.75 x 17.5, 10-hole, with rim offset, silver

Drawgear


Fixed drawbar, 1,900 mm long, 40 mm drawbar eye, 5° angle,
with silent bushing
truck superstructure up to 550 mm
Truck coupling height, unladen: approx. 850 - 900 mm

Brake system


Brake system according to EC Directive 71/320 or EC E R13
Two-line brake
EBS - electronic brake system
Wabco 4S3M = both axles sensed
Spring-loaded parking brake on 2nd axle
Steel air tank

Floor


Softwood floor 50 mm, waterproofed, protruding approx. 5 - 10 mm beyond frame
profiles

Ramps


2 foldable, 1-part loading ramps, approx. 2,800/710 mm, with hardwood flooring
Ramp width manually adjustable by approx. 550 mm, with rod,
(min. spacing approx. 295 mm up to max. total width of 2,815 mm)
lockable in driving position using chains with turnbuckle
2 autom. folding supports at rear
Lifting aid with coil spring

Electrical equipment


24 V lighting system according to EC Directive 76/756/E WG
2 five-chamber tail lights on ramps
LED side marker lights
2 clearance lamps
2 contour lights
Fixed cable(s) with 2 x 7-pin or 1 x 15-pin connector

Paintwork


Blasted with steel granulate, treated with zinc dust primer and spray painted
2-component acrylic paints for commercial vehicles (standard RAL or truck colour)

Plastic and hot-dip galvanised parts (extensions etc.) unpainted,
powder-coated attachments/installation parts and drawbar black

Reflective contour marking strips across entire length of sides and on the rear (white on sides and red at rear by default), according to ECE 48

Accessories


Rear markings as per ECE standards

Attachments


Wheel chock(s) as per regulations
Plastic mudguards or splashguards with spray protection as per regulations
Side impact protection
Spare wheel well for 1 spare wheel
Centre of gravity marking

Product impressions